Methods To Punch A Hole In A Leather Belt

I might prefer to introduce you to considered one of my all time favorite style tools… the Leather Hole puncher ! Perhaps you misplaced or gained some weight; maybe you discovered the right belt at a thrift retailer, but it surely's a not the precise dimension; perhaps you need a Hole between two of the already existing holes-regardless of the situation is, this tutorial will show you methods to add good spherical belt holes. Use a bit of scrap Leather beneath the belt, so that you're not hammering the punch proper into the anvil. The new holes look slightly more ragged across the edges, but utilizing the belt will help to smooth them down.
Be certain to put something, that you don't thoughts damaging, that doesn't move around behind the belt, that's thick enough, for when the drill bit goes by. This method takes longer than the others, and you might end up with a messy Hole. You should purchase oval-formed Leather Hole punches, but most people won't discover a mixture of spherical and oval holes.



Work slowly and punctiliously-this high sew will preserve your belt together, but it can also look fantastically embellished if it's done well! Start on the underside nook of the tail end (where you possibly can see I left the threads on the left side), go down the end, after which pivot at the corner to turn and continue all the best way down the size of your belt. It shouldn't take much thread, but be further careful in the event you're working with a thicker fabric.
Since you need to have more than sufficient further fabric to work with from your 1/four yard of material, cut a few pieces off in the path of the grain your material might be in on your ultimate product and measure out how vast your belt shall be. Do not just go by the width of the buckle's proper facet; your belt needs to have the ability to slide comfortably over the facet the place the clasp will rest on the left aspect.

You want to strive on the belt and get an idea for a way much you will need to deliver the belt in, one additional Hole is all i needed for this one. Some belts have screws near the buckle which you'll be able to remove and relocate to shrink the belt. I haven't got a Leather Hole punch, so I just used a nail that I had and punched the outlet a couple of times.
At this point, you could possibly use your Leather binder (should you're using Leather like I did) or rubber cement to coat the uncooked edges of this Hole you just punched to maintain the material from coming apart. Find the place you want the belt to be tightened to so it sits comfortably the place you will be carrying it and mark this point together with your tailor's chalk. Remove your belt and use a tape measure to mark where the other holes should be. I marked two on each side of the primary marking I made about 1″ in. aside each. It will let you use your belt regardless for those who want it to be looser or tighter!
Apply on the very end (that you're going to minimize off later) to get a really feel for a way the drill and Leather work together. Appears to be like like the Tandy Leather website store has gone kaput, the belt clean and belt hold hyperlinks don't work any longer. Tom, Sadly it seems like this published around the same time Tandy did a price increase on the belt clean. Tom: $7 balm + $1 hold + $2 buckle + $19 belt clean = $29 - $10 from code = $19. I already have Sno Seal at residence and want to avoid buying the Leather Balm if it does the same factor.

If you just want so as to add holes to a belt you have already got, this is likely to be for you, for those who simply must punch 10 holes or so it might even be positive make hole in belt, but for giant projects I'd recommend finding one thing higher, perhaps a set that you just hammer with a mallet. For the subsequent step, we have to minimize a Hole for where the arm of the buckle will go through.
Take a tape measure and determine the width of your hips, or wherever your belt shall be sitting if you put on it. Whatever number you provide you with, add about 8-10″ in. This ought to be the length of the material for your belt altogether! This material has a backing and is thick sufficient with only one layer, so I only needed to cut one piece for the belt. With this Leather cloth, I needed to trim the perimeters so the edges lined up nicely with the squares of the basketwoven strips. You also needs to take the time to double-check that your strip of cloth on your belt will match now that it's trimmed down.

Leave a Reply

Your email address will not be published. Required fields are marked *